Black Box IC109A-R2 Instalační manuál Strana 140
- Strana / 164
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
134
3
© 2007 Schneider Electric. All Rights Reserved.63230-216-229-B1
Commissioning
Checking Sepam™ B83
Additional Phase Voltage
Input Connections
Description
Perform this check on Sepam™ B83 units with additional phase voltage measurement. This does not check the main voltage input connections.
Since the additional voltages measured are unrelated to the currents measured by Sepam™ B83, it is not necessary to inject current to check
the Sepam™ B83 additional phase voltage input connections.
Block Diagram with Three Additional VTs
DE51260
* Detection of Plugged Connector (required for proper operation. Installed manually)
Procedure
Connect the voltage generator to the corresponding
test terminal box, using the plugs provided, according
to the diagram for the number of VTs connected to
Sepam™.
Perform the test in the next column as determined by
the generator you are using.
Procedure
Use the diagram above to perform the following tests.
Checking with a Three-Phase Voltage Generator
1 Turn the generator on.
2 Apply the three generator voltages Van, Vbn, Vcn, balanced and set to the rated
secondary phase-to-neutral voltage of the additional VTs (V’
Ln
s = V’
LL
s / 3).
3 Use the SFT2841 software to check that the values indicated for each of the phase-
to-neutral voltages V’an, V’bn, V’cn, and the positive sequence voltage V’1 are
approximately equal to the VT's rated primary phase-to-neutral voltage
(V’
Ln
p = V’
LL
p / 3)
4 Turn the generator off when you finish the test.
Checking with a Single-Phase Voltage Generator
1 Turn the generator on.
2 Apply the generator voltage V
N set to the rated secondary phase-to-neutral
voltage of the additional VTs (V’
Ln
s = V’
LL
s / 3) across the Sepam™ phase A
voltage input terminals.
3 Use the SFT2841 software to check that the value indicated for the phase-to-
neutral voltage V’an is approximately equal to the VT's rated primary phase-to-
neutral voltage (V’
Ln
p = V’
LL
p / 3).
4 Proceed in the same way by circular permutation with phase b and phase c
voltages, to check the V’bn and V’cn values.
5 Turn the generator off when you finish the test.
V‘an
V‘bn
V‘cn
V‘r
Vr
Vcn
Vbn
Van
- Series 80 1
- Protective Relays 1
- Safety Instructions 0 3
- Safety Instructions 8
- Before You Begin 8
- Introduction 10
- Modular Architecture 10
- Selection Table 11
- Technical Characteristics 13
- Environmental Characteristics 14
- Precautions 15
- Equipment Identification 16
- Main Units 18
- Accessories 19
- Replacement Equipment 20
- Base Unit 21
- Dimensions 21
- Mounting 22
- Connection 23
- Installing Terminal Guard 24
- Typical for Series 80 24
- CAUTION DANGER 25
- Installation 26
- Sepam™ B83 Connection Diagram 27
- Sepam™ C86 Connection Diagram 28
- Input for Sepam™ B80 34
- Connected Voltage Inputs 35
- 1A/5A Current Transformers 36
- Test Accessories 40
- CSH120 & CSH200 42
- Zero Sequence CT 42
- CSH30 Interposing Ring CT 44
- ACE990 Zero Sequence 47
- CT Interface 47
- Voltage Transformers 48
- MES120, MES120G, MES120H 50
- 14 Input/6 Output Modules 50
- Remote Modules 53
- MET1482 54
- Temperature Sensor Module 54
- Analog Output Module 56
- Remote Advanced UMI Module 58
- Sync-Check Module 60
- Communication Accessory 64
- Selection Guide 64
- Connection of Communication 65
- ACE937 Fiber Optic Interface 68
- ACE969TP and ACE969FO 69
- Multi-Protocol Interfaces 69
- Description 71
- RS232/RS485 Converter 74
- ACE919CA and ACE919CC 76
- RS485/RS485 Converters 76
- Communications Wiring 78
- Cable Pinouts 81
- Network Limits 82
- User-Machine Interfaces (UMI) 84
- User-Machine Interfaces 85
- DAMAGE TO CARTRIDGE 86
- CAUTION 87
- Local Operation on the UMI 88
- Password 91
- Settings 93
- SFT2841 Setup and Operating 96
- Welcome Window 96
- Connection Window 97
- SFT2841 Set Up and Operating 100
- Software 100
- General Screen Organization 100
- Using the Software 101
- Creating User Messages 102
- Disturbance Recording 103
- Logic-Equation Editing 104
- Program 105
- Default Settings 107
- Configuring Sepam™ 109
- SFT2841 Software 113
- Mimic-Diagram Editor 113
- Presentation 113
- Contents 123
- Principles 124
- Commissioning 125
- Equipment 126
- General Examination and 127
- Preliminary Actions 127
- Checking Input Connections 129
- 3-Phase Generator 129
- Single-Phase Generator & 130
- Voltages Delivered by 3 VT 130
- Checking Phase Current 132
- Input Connections 132
- For Differential Applications 132
- LPCT Type Current Sensors 133
- Checking Residual Current/ 134
- Voltage Input Connections 134
- Checking Residual Current 135
- Van = Vr 135
- Checking Residual Voltage 136
- Broken Delta Arrangement 136
- With Voltage Delivered by 137
- 1 Neutral Point VT 137
- Checking Sepam™ B80 138
- Additional Voltage 138
- Additional Voltage 139
- Checking Sepam™ B83 140
- Additional Phase Voltage 140
- Additional Residual Voltage 142
- Checking Sepam™ C86 143
- Unbalance Current 143
- Checking Logic Input & 144
- Output Connections 144
- Checking Optional 145
- Module Connections 145
- Validating the Complete 146
- Protection Chain 146
- Test Sheet 147
- Sepam™ Series 80 147
- Troubleshooting Assistance 152
- 152
- Replacing the Base Unit 156
- Replacing the Battery 156
- 3-Wire Power System 158
- 4-Wire Power System 159
- 63230-216-229-B1 161
- Schneider Electric USA 164
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce