Black Box 5000 Series Instalační příručka Strana 23
- Strana / 28
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
23
Quake Satellite Modem
Note: Installation must be performed in a known good cellular coverage area. The preferred
installation method and placement for the Quake satellite modem is mounted with zip ties
under the dashboard, near the Networkfleet unit. If there is no room to do this, then the
option is to secure the modem elsewhere in the vehicle with zip ties, screws, or strong two-
sided tape as necessary
Installation Process:
1. Inspect the vehicle and determine where the Networkfleet unit and Quake satellite
modem will be mounted.
2. Determine the path you will use to extend the Quake satellite modem antenna to
its mounting location on the roof of the vehicle. Thoroughly clean the mounting
location on the roof of the vehicle with an alcohol pad (not included) prior to affixing
antenna.
a. The antenna should be mounted in a location that offers full horizon-to-
horizon visibility. It should be flat and parallel with the ground with the
non-magnetic side pointing straight up.
b. Avoid pinch points which can damage the coaxial cable or its shielding.
c. Antenna exit points will vary based on the type of vehicle. Choose from
the common points of exit listed below:
i. Door/Windshield weather stripping
ii. Trunk lid
iii. Firewall pass-thru
3. Connect the Quake modem data harness cable and coaxial antenna cable to the
Quake modem, then mount the Quake modem.
4. Connect the red wire from Quake modem data harness to a constant +12V battery
source.
5. Remove Networkfleet unit knock-out plate and connect the Quake modem data
harness to the Networkfleet unit’s 8 pin serial port.
6. If the Networkfleet unit is not already mounted and powered up, mount the
Networkfleet unit per existing installation standards and connect the Networkfleet
unit to power using its power harness.
7. Start the vehicle and let it idle 15 minutes before calling Customer Care to verify the installation is successful.
For Antenna Removal
It is recommended that removal of the antenna happen at a time when the surface of the vehicle is at a low temperature.
- 5000 PRODUCT LINE 1
- INSTALLATION GUIDE 1
- Table of Contents 2
- Registration Form 3
- 6-pin Harness 6
- 9-pin “D” Harness 6
- 9-pin Harness 6
- Networkfleet Unit 9
- Core Connector 9
- Bypass Connector 9
- Original OBD-II Port 9
- To Vehicle 9
- LED Indicator Lights 13
- Side of Unit 13
- Creating Tamper Evidence 14
- Completing Installation 15
- Securing the Device 16
- Window-Mount GPS Antenna 17
- Sensor 18
- Data Port 19
- Sensor Port 19
- Serial Port 19
- Sensor Input Harness 19
- (Blue & Purple) 19
- Port Expansion Module (PEM) 22
- Quake Satellite Modem 23
- Pelican Micro Case 25
- Frequently Asked Questions 27
- Contacting Networkfleet 28
Související produkty a manuály pro Sítě Black Box 5000 Series
Sítě Black Box MD403A Specifikace
(20 stránky)
(20 stránky)
Sítě Black Box CSU/DSU Specifikace
(116 stránky)
(116 stránky)
Sítě Black Box ACS111 Průvodce nastavením
(148 stránky)
(148 stránky)
Sítě Black Box CSU/DSU Specifikace
(27 stránky)
(27 stránky)
Sítě Black Box ME265C Uživatelský manuál
(1 stránky)
(1 stránky)
Sítě Black Box LE3700A-R2 Specifikace
(67 stránky)
(67 stránky)
Sítě Black Box MDS920C-10BT Uživatelský manuál
(29 stránky)
(29 stránky)
Sítě Black Box Lineshare Pro AC FX150A Specifikace
(27 stránky)
(27 stránky)
Sítě Black Box DEH-P7300R Uživatelský manuál
(11 stránky)
(11 stránky)
Sítě Black Box IEEE 1284 Specifikace
(15 stránky)
(15 stránky)
Sítě Black Box ME265C Specifikace
(50 stránky)
(50 stránky)
Sítě Black Box 3600 Uživatelský manuál
(2 stránky)
(2 stránky)
Sítě Black Box ME265C Uživatelský manuál
(2 stránky)
(2 stránky)
Pach-and-company AeGIS 7000P Series Quick Guide manuals
Owner’s manuals and user’s guides for Accessories communication Pach-and-company AeGIS 7000P Series Quick Guide.
We providing 1 pdf manuals Pach-and-company AeGIS 7000P Series Quick Guide for download free by document types: User Manual
Komentáře k této Příručce